It's time I built a D3a -> 5687 phonostage
- IslandPink
- Amstrad Tower of Power
- Posts: 10041
- Joined: Tue May 29, 2007 7:01 pm
- Location: Denbigh, N.Wales
#16 Re: It's time I built a D3a -> 5687 phonostage
Oh well done Dave. I know I saved it myself but god knows where I put it !
Edit : just threw a page ( again ) ... so annoying. Here's the circuit again -
Edit : just threw a page ( again ) ... so annoying. Here's the circuit again -
"Once you find out ... the Circumstances ; then you can go out"
- Thermionic Idler
- Old Hand
- Posts: 1056
- Joined: Sun Apr 22, 2012 8:22 pm
- Location: Southsea
#17 Re: It's time I built a D3a -> 5687 phonostage
My search foo is good today! Though I see some battles with Spice on the horizon...
Thanks Mark - that image is a bit clearer. The only thing I still cannot make out is the value of the two caps in parallel going to the three pin connector from the 5687 cathode (which I presume is the interface to the RIAA).
Thanks Mark - that image is a bit clearer. The only thing I still cannot make out is the value of the two caps in parallel going to the three pin connector from the 5687 cathode (which I presume is the interface to the RIAA).
Deck: Garrard 301 - Audio Origami PU7 - NW Analogue DH3S
Phono: Pete Millett LR, Lundahl SUT, AMB σ22 PSU
Linestage: Bruno Putzeys Balanced Pre + Hans Polak relay mod, LCDuino control
Power amps: 300B PP 'Symmetric Reichert'
Speakers: FF225WK Big Mets
Phono: Pete Millett LR, Lundahl SUT, AMB σ22 PSU
Linestage: Bruno Putzeys Balanced Pre + Hans Polak relay mod, LCDuino control
Power amps: 300B PP 'Symmetric Reichert'
Speakers: FF225WK Big Mets
#18 Re: It's time I built a D3a -> 5687 phonostage
Yes. Two 33uf films
Whenever an honest man discovers that he's mistaken, he will either cease to be mistaken or he will cease to be honest.
- Thermionic Idler
- Old Hand
- Posts: 1056
- Joined: Sun Apr 22, 2012 8:22 pm
- Location: Southsea
#19 Re: It's time I built a D3a -> 5687 phonostage
Thanks Nick.
Well, this is frustrating. I've laid out the first stage in Spice so that I can study the circuit and work out what's going on. Unfortunately, I'm getting next to no gain (in fact it's a loss), there's almost nothing on the 5687 cathode. The current going through the first two MOSFETS is on the nA / pA scale and I think that might be the issue. Spice doesn't have IRF740 in its library of N channel MOSFETS so I've been trying to find the nearest match in an effort to get the thing up and running at the very least, even if the sim wasn't 100% accurate. I've tried several but same result. Maybe the MOSFET models are junk.
I've double checked the circuit several times and I don't think I've got anything wrong...
Well, this is frustrating. I've laid out the first stage in Spice so that I can study the circuit and work out what's going on. Unfortunately, I'm getting next to no gain (in fact it's a loss), there's almost nothing on the 5687 cathode. The current going through the first two MOSFETS is on the nA / pA scale and I think that might be the issue. Spice doesn't have IRF740 in its library of N channel MOSFETS so I've been trying to find the nearest match in an effort to get the thing up and running at the very least, even if the sim wasn't 100% accurate. I've tried several but same result. Maybe the MOSFET models are junk.
I've double checked the circuit several times and I don't think I've got anything wrong...
Deck: Garrard 301 - Audio Origami PU7 - NW Analogue DH3S
Phono: Pete Millett LR, Lundahl SUT, AMB σ22 PSU
Linestage: Bruno Putzeys Balanced Pre + Hans Polak relay mod, LCDuino control
Power amps: 300B PP 'Symmetric Reichert'
Speakers: FF225WK Big Mets
Phono: Pete Millett LR, Lundahl SUT, AMB σ22 PSU
Linestage: Bruno Putzeys Balanced Pre + Hans Polak relay mod, LCDuino control
Power amps: 300B PP 'Symmetric Reichert'
Speakers: FF225WK Big Mets
#20 Re: It's time I built a D3a -> 5687 phonostage
What you have missed is the line that says that the depletion mosfets are IXTP08N100's I just used the 740 models as they have the same pinout. The mosfet that's driving the d3a g2 is a STU3N45K3, but most high voltage N chan will be fine there I just wanted one with a low Cgs
Whenever an honest man discovers that he's mistaken, he will either cease to be mistaken or he will cease to be honest.
- Thermionic Idler
- Old Hand
- Posts: 1056
- Joined: Sun Apr 22, 2012 8:22 pm
- Location: Southsea
#21 Re: It's time I built a D3a -> 5687 phonostage
Ahhhhh... like footprints in KiCAD, yes I've used the same trick sometimes. That explains it.Nick wrote: Mon Feb 20, 2023 1:29 pm What you have missed is the line that says that the depletion mosfets are IXTP08N100's I just used the 740 models as they have the same pinout. The mosfet that's driving the d3a g2 is a STU3N45K3, but most high voltage N chan will be fine there I just wanted one with a low Cgs
Looks like I'll have to go and find a model for that, it's (predictably) not in the list of available NMOS devices...
Deck: Garrard 301 - Audio Origami PU7 - NW Analogue DH3S
Phono: Pete Millett LR, Lundahl SUT, AMB σ22 PSU
Linestage: Bruno Putzeys Balanced Pre + Hans Polak relay mod, LCDuino control
Power amps: 300B PP 'Symmetric Reichert'
Speakers: FF225WK Big Mets
Phono: Pete Millett LR, Lundahl SUT, AMB σ22 PSU
Linestage: Bruno Putzeys Balanced Pre + Hans Polak relay mod, LCDuino control
Power amps: 300B PP 'Symmetric Reichert'
Speakers: FF225WK Big Mets
- Thermionic Idler
- Old Hand
- Posts: 1056
- Joined: Sun Apr 22, 2012 8:22 pm
- Location: Southsea
#22 Re: It's time I built a D3a -> 5687 phonostage
Fixed it! Found a model on https://www.diyaudio.com/community/thre ... el.307318/ which makes use of the VDMOS model, pasted it into standard.mos and I was able to pick it as a transistor.
Sim seems to work now, I get about 44dB gain before it hits the RIAA and the various current figures seem to be about where they should be.
Sim seems to work now, I get about 44dB gain before it hits the RIAA and the various current figures seem to be about where they should be.
Deck: Garrard 301 - Audio Origami PU7 - NW Analogue DH3S
Phono: Pete Millett LR, Lundahl SUT, AMB σ22 PSU
Linestage: Bruno Putzeys Balanced Pre + Hans Polak relay mod, LCDuino control
Power amps: 300B PP 'Symmetric Reichert'
Speakers: FF225WK Big Mets
Phono: Pete Millett LR, Lundahl SUT, AMB σ22 PSU
Linestage: Bruno Putzeys Balanced Pre + Hans Polak relay mod, LCDuino control
Power amps: 300B PP 'Symmetric Reichert'
Speakers: FF225WK Big Mets
#23 Re: It's time I built a D3a -> 5687 phonostage
That sounds about right. In practice I get 40dB for the first stage, its controlled by the feedback percentage set by R22 and R23 in your model.
Whenever an honest man discovers that he's mistaken, he will either cease to be mistaken or he will cease to be honest.
- Thermionic Idler
- Old Hand
- Posts: 1056
- Joined: Sun Apr 22, 2012 8:22 pm
- Location: Southsea
#24 Re: It's time I built a D3a -> 5687 phonostage
So post-RIAA I go a bit off-piste:
I was looking at the output stage of Stephen's (izzy-wizzy) circuit and couldn't help noticing a similarity to Lynn Olson's Raven. This is a version of that, with rough resistor values in there for now.
Gain of the whole thing is modelling at 40dB at the 1kHz point.
I was looking at the output stage of Stephen's (izzy-wizzy) circuit and couldn't help noticing a similarity to Lynn Olson's Raven. This is a version of that, with rough resistor values in there for now.
Gain of the whole thing is modelling at 40dB at the 1kHz point.
Deck: Garrard 301 - Audio Origami PU7 - NW Analogue DH3S
Phono: Pete Millett LR, Lundahl SUT, AMB σ22 PSU
Linestage: Bruno Putzeys Balanced Pre + Hans Polak relay mod, LCDuino control
Power amps: 300B PP 'Symmetric Reichert'
Speakers: FF225WK Big Mets
Phono: Pete Millett LR, Lundahl SUT, AMB σ22 PSU
Linestage: Bruno Putzeys Balanced Pre + Hans Polak relay mod, LCDuino control
Power amps: 300B PP 'Symmetric Reichert'
Speakers: FF225WK Big Mets
- izzy wizzy
- Needs to get out more
- Posts: 1550
- Joined: Fri Nov 02, 2007 7:02 pm
- Location: Auckland NZ
- Contact:
#25 Re: It's time I built a D3a -> 5687 phonostage
With that lcr, don't you either have to drive it with a 600R source or terminate it with 600R?
I might have missed something with the driver as I'm looking at it on a phone.
I might have missed something with the driver as I'm looking at it on a phone.
#26 Re: It's time I built a D3a -> 5687 phonostage
In the case of the original, its a 1k5 LCR and its terminated on the LCR board. The inductors are connected to a board that contains the caps and resistors.
Whenever an honest man discovers that he's mistaken, he will either cease to be mistaken or he will cease to be honest.
- IslandPink
- Amstrad Tower of Power
- Posts: 10041
- Joined: Tue May 29, 2007 7:01 pm
- Location: Denbigh, N.Wales
#27 Re: It's time I built a D3a -> 5687 phonostage
Yes, of course, i asked you similar questions when I first saw the circuit.
So that's the reason for the 2 x 33uF caps from the 5687 CF - to get a low time constant with the 1.5K termination.
So that's the reason for the 2 x 33uF caps from the 5687 CF - to get a low time constant with the 1.5K termination.
"Once you find out ... the Circumstances ; then you can go out"
- IslandPink
- Amstrad Tower of Power
- Posts: 10041
- Joined: Tue May 29, 2007 7:01 pm
- Location: Denbigh, N.Wales
#28 Re: It's time I built a D3a -> 5687 phonostage
Sorry Gm stageIslandPink wrote: Sat Feb 18, 2023 5:01 pm ... the previous Pentode mu-stage, to help stabilise it ....
"Once you find out ... the Circumstances ; then you can go out"
- Thermionic Idler
- Old Hand
- Posts: 1056
- Joined: Sun Apr 22, 2012 8:22 pm
- Location: Southsea
#29 Re: It's time I built a D3a -> 5687 phonostage
So with a 600R termination it looks like those values need to go up a bit.IslandPink wrote: Tue Feb 21, 2023 6:38 pm Yes, of course, i asked you similar questions when I first saw the circuit.
So that's the reason for the 2 x 33uF caps from the 5687 CF - to get a low time constant with the 1.5K termination.
Deck: Garrard 301 - Audio Origami PU7 - NW Analogue DH3S
Phono: Pete Millett LR, Lundahl SUT, AMB σ22 PSU
Linestage: Bruno Putzeys Balanced Pre + Hans Polak relay mod, LCDuino control
Power amps: 300B PP 'Symmetric Reichert'
Speakers: FF225WK Big Mets
Phono: Pete Millett LR, Lundahl SUT, AMB σ22 PSU
Linestage: Bruno Putzeys Balanced Pre + Hans Polak relay mod, LCDuino control
Power amps: 300B PP 'Symmetric Reichert'
Speakers: FF225WK Big Mets
- izzy wizzy
- Needs to get out more
- Posts: 1550
- Joined: Fri Nov 02, 2007 7:02 pm
- Location: Auckland NZ
- Contact:
#30 Re: It's time I built a D3a -> 5687 phonostage
The classic 600r lcr module can cause some issues which is why some of late have taken a different course of higher Z all the way to 10k. 1.5k or thereabouts is seen as a "better" bet to keep away the issues associated with much higher z.
Some get rid of the requirement of a huge coupling cap and DC couple to lcr and small cap after or something else. But then you need the lcr to not have a DC path to ground. I think that particular lcr configure isn't the most accurate configuration.
As always, there ain't no free lunch.
Some get rid of the requirement of a huge coupling cap and DC couple to lcr and small cap after or something else. But then you need the lcr to not have a DC path to ground. I think that particular lcr configure isn't the most accurate configuration.
As always, there ain't no free lunch.