DHT Heater Group Buy notes.

Assorted info that will be of use, spec sheets, docs etc. Non informational postings will be removed.
Andrew
Eternally single
Posts: 4206
Joined: Thu May 24, 2007 2:18 pm

#31 Re: DHT Heater Group Buy notes.

Post by Andrew »

I should add that I have not had any reports of the non-epoxy cap breaking on the PCBs in the field. Doesn't mean it hasn't happended but I've not heard about it....if it has.
Analogue, the lost world that lies between 0 and 1.
User avatar
Mike H
Amstrad Tower of Power
Posts: 20156
Joined: Sat Oct 04, 2008 5:38 pm
Location: The Fens
Contact:

#32 Re: DHT Heater Group Buy notes.

Post by Mike H »

Fascinating.

Image
 
"No matter how fast light travels it finds that the darkness has always got there first, and is waiting for it."
User avatar
izzy wizzy
Old Hand
Posts: 1496
Joined: Fri Nov 02, 2007 7:02 pm
Location: Auckland NZ
Contact:

#33 Re: DHT Heater Group Buy notes.

Post by izzy wizzy »

The diodes DSB10I45PM are hard to get or on long back order from Farnell
https://uk.farnell.com/ixys-semiconduct ... w%2Fsearch.

I found these
https://uk.farnell.com/stmicroelectroni ... dp/2325859

I know they're duals so I figured I could use 3; the common cathode being used for the positive leg of the bridge and use them as singles for the negative leg. I thought they were close in spec to the originals if I'm looking at the right things; a low Vf fer instance.

These are a small signal schottky like the originals. What is the difference between a small signal schottky and a schottky rectifier?

If these were OK, they have a low Vf and I'm using only 5VAC in for 2.1V out to 4P1L
https://uk.farnell.com/stmicroelectroni ... dp/9803360

Cheers,
Stephen
User avatar
Nick
Site Admin
Posts: 15694
Joined: Sun May 06, 2007 10:20 am
Location: West Yorkshire

#34 Re: DHT Heater Group Buy notes.

Post by Nick »

I use these all the time

https://uk.farnell.com/stmicroelectroni ... t=STPS1045

Slightly higher Vf, but don't know if 60mv matters.
Whenever an honest man discovers that he's mistaken, he will either cease to be mistaken or he will cease to be honest.
User avatar
izzy wizzy
Old Hand
Posts: 1496
Joined: Fri Nov 02, 2007 7:02 pm
Location: Auckland NZ
Contact:

#35 Re: DHT Heater Group Buy notes.

Post by izzy wizzy »

Nick wrote: Fri Jun 21, 2019 8:45 am I use these all the time
https://uk.farnell.com/stmicroelectroni ... t=STPS1045
Slightly higher Vf, but don't know if 60mv matters.
Thanks Nick. I've gone with these,
Andrew
Eternally single
Posts: 4206
Joined: Thu May 24, 2007 2:18 pm

#36 Re: DHT Heater Group Buy notes.

Post by Andrew »

Yep, Nick's suggestion should be fine :)
Analogue, the lost world that lies between 0 and 1.
User avatar
Ray P
No idea why I do this anymore
Posts: 6292
Joined: Thu Nov 22, 2007 5:18 pm
Location: Somerset

#37 Re: DHT Heater Group Buy notes.

Post by Ray P »

Andrew wrote: Tue Jan 12, 2016 12:11 pm The parts that that are best not substituted include the 470nF surface mount caps and the carbon comp resistors, please get the exact ones listed in the BOM.

It looks as though the carbon comp resistors listed in the BOM are now obsolete - I substituted similar of good quality.
Sorry, I couldn't resist!
User avatar
Ray P
No idea why I do this anymore
Posts: 6292
Joined: Thu Nov 22, 2007 5:18 pm
Location: Somerset

#38 Re: DHT Heater Group Buy notes.

Post by Ray P »

I'm assembling a couple of boards for my Bartola 2P29L preamp project and need an output of 9.3V - would prefer to populate Rx & Ry rather than using a trim pot but I'm not sure how to derive the values?

I'm upgrading the filter caps to accomodate the higher AC voltage Tx I'll need to use.
Sorry, I couldn't resist!
User avatar
Ray P
No idea why I do this anymore
Posts: 6292
Joined: Thu Nov 22, 2007 5:18 pm
Location: Somerset

#39 Re: DHT Heater Group Buy notes.

Post by Ray P »

So I found this on the main thread;
Andrew wrote: Mon Jun 09, 2014 7:18 pm
IslandPink wrote: (i) what values of Rx , Ry should I be using for 20V-out on the big boards ?
Its basically Vout = 2.5v(1 + Rx/Ry), something like 6k8/1k might be a good place to start.

It's all in here. http://www.ti.com/lit/an/slva445/slva445.pdf
Last edited by Ray P on Fri Feb 05, 2021 9:32 am, edited 1 time in total.
Sorry, I couldn't resist!
User avatar
Ray P
No idea why I do this anymore
Posts: 6292
Joined: Thu Nov 22, 2007 5:18 pm
Location: Somerset

#40 Re: DHT Heater Group Buy notes.

Post by Ray P »

Using the information in the previous post I should get 9.3V out with Rx=6K8 and Ry=2K5

I'm assuming the use of a 12VAC or 15VAC Tx. 2P29L was designed for battery use so filament current is only 120mA so I'm not anticipating heat dissipation issues.

I'll be using the 'large' PCBs because of the lower physical profile.
Sorry, I couldn't resist!
User avatar
Ray P
No idea why I do this anymore
Posts: 6292
Joined: Thu Nov 22, 2007 5:18 pm
Location: Somerset

#41 Re: DHT Heater Group Buy notes.

Post by Ray P »

I also tracked down in the main thread the mechanical drawing of the 'large' PCB so posting it here for reference.
layout_mk10_dims.png
I measured the corner mounting holes pitches as 38.5mm and 74mm
Sorry, I couldn't resist!
User avatar
IslandPink
Amstrad Tower of Power
Posts: 10041
Joined: Tue May 29, 2007 7:01 pm
Location: Denbigh, N.Wales

#42 Re: DHT Heater Group Buy notes.

Post by IslandPink »

Here's a link to the original thread about the development.
Just putting it here because it took me a while to find it, just now :

https://www.audio-talk.co.uk/phpBB3/vie ... php?t=4729
"Once you find out ... the Circumstances ; then you can go out"
Post Reply